Tools, Parts, & Supplies
Below is a searchable list of some of the tools, parts, and supplies that I have used in the past for various projects.
Please note that the prices may vary from when I purchased them and it's possible that links may become outdated or broken.
*Disclosure: As an Amazon Associate I may earn from qualifying purchases that originate from any of the affiliate links I have shared on this website.
− Bearing Separator Puller Set
Useful for pulling bearings that have gotten stuck or bonded to the axle.
Categories: Bearings, OneWheel XR, OneWheel GT
− Hex Head Allen Wrench Drill Bits Long
Great Hex Allen set that has all the sizes needed for the XR as well as a few others.
Categories: Drill Bits, Bits, OneWheel XR
− 6 Point Torx Plus Bit Socket Set, 1/4-Inch, 3/8-Inch and 1/2-Inch Drive, TP8 - TP60, 12-Piece
Torx plus bit socket set that has the bit needed for removing GT axle bolts.
Categories: Socket Set, Torx Plus, Bits, OneWheel GT
− 90 Degree HSS Chamfering Tool Bit Countersink Drill Bit Set
Chamfering bits that I use to countersink holes on additional aluminum lid plates or thicker aluminum lids/plates.
Categories: Bits, Drill Bits, Metal Working
− Drill Brush Power Scrubber Cleaning Brush Extended Long Attachment Set All Purpose Drill Scrub Brushes Kit
Brushes that attach to a drill for easier cleaning of grip tape and other stuff.
Categories: Cleaning, Brushes, Grip Tape Cleaning
− Molex Crimpers (Weather Pack Crimper Tools for Delphi APTIV)
I use this for crimping terminal ends for the 16 pin and 6 pin molex connectors that Future Motion uses for the main harness and motor harness connections on their stock controller boxes.
Categories: Crimpers, Hand Tools, Molex
− JST Cimpers (iCrimp IWS-3220M Micro Connector Pin Crimping Tool 32-20AWG)
I use this mainly to modify existing JST cables or create new JST cables that are needed for connecting to a VESC controller or otherwise.
Categories: JST, Crimpers, Hand Tools
− Small Electronics Breadboard Test Kit
A decent cheap kit that can be used for low voltage/low amp electronics testing. ELEGOO Upgraded Electronics Fun Kit w/ Power Supply Module, Jumper Wire, Precision Potentiometer, 830 tie-Points Breadboard Compatible with Arduino, STM32.
Categories: Electronics Testing
− DC Power Supply 120v 3A
A decent and affordable bench DC power supply. IKococater DC Power Supply Variable 120V 3A with Output Switch, Adjustable Regulated Switching Bench Power Supply with 4-Digits LED Power Display, 5V/2A USB Interface, Accurate Encoder Adjustment Knob
Categories: Electronics Testing, DC Power Supplies
− AstroAI Digital AC/DC Multimeter
A decent and affordable multi-meter. AstroAI Digital Multimeter TRMS 4000 Counts with DC AC voltmeter and Auto-Ranging Fast Accurately Measures Voltage, Current, Resistance, Capacitance, Temperature, Continuity, Frequency and Duty-Cycle.
Categories: Electronics Testing, Multimeters
− KP184 DC Electronic Load Tester
Decent DC Load Tester. Useful for draining batteries down to a desired voltage or just general DC load testing. KP184 DC Electronic Load Battery Capacity Tester Internal Resistance Tester Power Tester RS485/232 400W 40A Digital Display US Stock.
Categories: Electronics Testing, DC Load Testers
− Starrett Steel Automatic Center Punch
Quality center punch for various use cases. Screw extraction being one. Starrett Steel Automatic Center Punch with Adjustable Stroke - 5-1/4" Length, 11/16" Punch Diameter, Lightweight, Knurled Steel Handle - 18C
Categories: Center Punch, Hand Tools, Screw Extraction
− Metric Nut Driver Set
Metric nut driver set. The M3.5 is really the main one you need for the m3 nuts used with the flowglider box. Pro'sKit 1PK-9402 Hex Nut Driver Set, Yellow
Categories: Hand Tools, Nut Drivers, VESC, Lil FOCer BYOH, Lid Mount
− 1/8-Inch Hex Key with Journeyman T-Handle
Great hex allen tool for the 1/8 inch hardware that is most common on the XR. Klein Tools JTH6E08 1/8-Inch Hex Key with Journeyman T-Handle, 6-Inch
Categories: OneWheel XR, Hex, Allen, Hand Tools
− Digital Caliper - Millimeter / Inch / Fractions
A decent set of calipers for making small measurements. NEIKO 01407A Electronic Digital Caliper | 0-6 Inches | Stainless Steel Construction with Large LCD Screen | Quick Change Button for Inch/Fraction/Millimeter Conversions
Categories: Measuring, Calipers, Precision Measurements
− Smoke Diffuser/Absorber for Soldering
Decent for difusing fumes while soldering so you are not getting blasted with high concentrations of solder smoke right to the face. KOTTO Strong Suction Hose Fume Smoke Absorber for Soldering, Electric Iron Welding, 3d Printing Extractor Absorber Remover DIY Extractor Carbon or HEPA Filter.
Categories: Soldering, Fumes, Smoke
− Weller Digital Soldering Station - WE1010NA
There many solder station options. This just happens to be the one I use. Weller Digital Soldering Station - WE1010NA
Categories: Soldering, Brass Inserts, Electronics
− Genuine Weller Soldering Tip Set
Soldering tips that I use with my soldering station. Genuine Weller WE1010 Soldering Tip Set (ETSET-5)- ETA, ETB, ETC, ETP, TETS, 5 PCS
Categories: Soldering
− Magnetic Helping Hands Third Arm
A decent set of helping hands that I use when soldering. Magnetic Helping Hands Third Arm Soldering Work Station | EXtra Large & Heavy Duty Base Plate | 5 Flexible Arms with Precision 360 Degree Alligator Clip
Categories: Soldering, Electronics
− Wagner Heat Gun
A decent heat gun that I use on a regular basis for applying heat shrink to solder connections. I have also used it very carefully on low to remove grip tape. Wagner Spraytech 0503008 HT1000 Heat Gun, 2 Temp Settings 750?F & 1000?F, Great for Soften paint, Caulking, Adhesive, Putty Removal, Shrink Wrap, Bend Plastic Pipes, Loosen Rusted Nuts or Bolts
Categories: Soldering, Grip Tape Removal
− 1/4 In. T-Handle Tap Wrench
Used to securely hold taps that are to be turned by hand. (Tap threads). BOSCH BTH014#0-1/4 In. T-Handle Tap Wrench.
Categories: Thread Repair
− #10-32 UNF Steel Plug Tap
Tap used for cleaning or making new threads on XR Rails. Footpad screws, etc. Drill America - DWT54357 #10-32 UNF High Speed Steel Plug Tap.
Categories: Thread Repair, OneWheel XR, OneWheel XR Rail Threads
− Hydraulic Wire Battery Cable Lug Terminal Crimper Crimping Tool
This is not an out of the box solution, but this tool can be modified in a way that it can be used for pressing replacement threaded inserts into rails and other components.
Categories: Thread Repair, Threaded Press Inserts
− Soldering Tips for Pressing in Heat Set inserts.
Soldering Iron tips designed specifically for use with brass inserts that need to be melted into 3d printed or other plastic items. Virtjoule Heat Set Insert Tips for Sizes M2, M2.5, M3, M4, and M5 - Soldering Iron Tips for 3D Printer Users, 3D Printing Accessories Compatible with Weller WES51/WESD51 Soldering Iron.
Categories: Threaded Inserts, 3D Printed VESC Controller Box
− X-ACTO Compression Basic Knife Set
X-Acto knife kit. I feel this is a must have. Useful for so many things. Besides the usual cutting, I often use them to lift the locking tabs on small JST connectors. X-ACTO Compression Basic Knife Set.
Categories: Various, Cutting, Precision Cutting
− Self-Healing Cutting Mat
A decent cutting mat, but I also like to use this as my work surface. Makes it super easy to pick up and dump dirt and wire clippings in the trash throughout the build process. Keeping your workspace cleaner. Also good for cutting thermal pads. Dahle Vantage 10672 Self-Healing Cutting Mat, 18"x24", 1/2" Grid, 5 Layers for Max Healing, Perfect for Crafts & Sewing, Black.
Categories: Various, Cutting
− Small Hot Glue Gun
A cheap and small hot glue gun that comes with plenty of glue sticks. I prefer the smaller size when working in tight spaces. Assark Glue Gun, Mini Hot Glue Gun Kit with 30 Glue Sticks for School Crafts DIY Arts Quick Home Repairs, 20W (Blue).
Categories: Various, Adhesive, Glue
− Rotary Tool Accessories Kit, 357 Pcs Accessories
A decently priced assortment of Dremel attachments. APEXFORGE M0 Rotary Tool Accessories Kit, 357 Pcs Accessories, 1/8"(3.2mm) Diameter Shanks, Universal Fitment for Easy Cutting, Sanding, Grinding, Sharpening, Carving, Drilling, and Engraving.
Categories: Various, Cutting, Grinding, Dremel
− SeeedStudio - Grove - Buzzer
Buzzer that works will with VESC/ LilFOCer. I feel this is a necessary upgrade at usually less than $5. Lets you know when you have left your board turned on amongst other things. SeeedStudio - Grove - Buzzer - Generate Various Tones and Effects.
Categories: Buzzer, VESC Alerts, Lil FOCer, Float Package
− Neutrik NC4FXX XLR 4 Pin, Cable Mount, Metal Body, Silver Plated
Female 4 pin XLR plug that I use for any non-15s board charger. I do this to prevent someone plugging in a 15s 3pin FM XR charger into my boards. I wire 18s,19s, and 20s differently using the available pins. Neutrik NC4FXX XLR Audio Connector, Jack, 4, Cable Mount, Metal Body, Silver Plateds. See our wiring guide under Scripts(Rx).
Categories: Connectors, XLR, Charging, Charger
− Neutrik NC4MPR-HD XLR 4 Pin, Male. Controller Mount.
Male 4 pin XLR port that I use on any non-15s board. I do this to prevent someone plugging in a 15s 3pin FM XR charger into my boards. I wire 18s,19s, and 20s differently using the available pins. Neutrik NC4MPR-HD XLR Audio Connector, Plug, 4, Panel Mount, Metal Body, Gold Plated.
Categories: Connectors, XLR, Charging, Charger
− MR30 Male Female Connectors
These are great for when you need a 3rd pin instead of the 2 pins on an xt30. Super useful in Conversions that utilize FM BMS that utilize 3 wires going to the 3 pin XLR. 20pair Amass MR30 Male Female Connector Plug with Sheath for RC Lipo Battery.
Categories: Connectors, Future Motion BMS, VESC FM BMS
− SwitchCraft 8 Pin Female Plug (EN3C8FX)
I have used these to run CAN wiring back to my battery box. Could also be used for wiring for lights. Various use cases. See this custom Flowglider box on THINGIVERSE.
Categories: Connectors, SwitchCraft, Charging Harness, CAN Bus
− Molex 6 pin housing mount (Floatboxx)
This is for the floatboxx or other custom boxes, this is NOT for the flowglider box. Needs waterproofing via silicone. Install your own pins using crimp tools. Molex 6 pin housing mount (0194290044).
Categories: Molex, Connectors, Motor Plug, Floatboxx
− 460PCS JST PH2.0 Connector kit
A decent JST connector kit. You will need crimpers for these. Crimping small JSTs can be tedious work. 460PCS JST PH2.0 Connector kit 2/3/4/5/6Pin Plug with Terminal Wires Cables Socket Header Wire Connectors Kit.
Categories: Connectors, JST
− SwitchCraft 6 Pin Male Connector mount (EN3P6MX)
6 Position Circular Connector Receptacle, Male Pins Solder Cup. Generally used for Hall Sensor and Footpad connectors in VESC and FM XR boards. SwitchCraft 6 Pin Male Connector mount (EN3P6MX).
Categories: Connectors, SwitchCraft, XR Hall Sensor Connector, XR Footpad Connector
− Molex 16 pin Male Panel Mount. (0194280016)
Mates with the 16 pin connector on the stock FM XR harnesses. Molex 16 pin Male Panel Mount. (0194280016)(SM7386-ND).
Categories: Connectors, Molex, OneWheel XR
− 20 Pairs XT30 Connectors (Male & Female)
XT30 Power connectors. Always check polarity. 20 Pairs XT30 Connectors Male and Female Connectors Plugs with 2 Pieces Shrink Tubing for RC Battery.
Categories: Connectors, XT30
− XT90 Anit-Spark connectors. 10 Pair (Male & Female)
XT90 Power connector with anti-spark. I use these most often on the main harness betweeen the battery and VESC controller. Always check polarity. SoloGood Amass 10 Pairs XT90S XT90-S XT90 Connector Anti-Spark Male Female Connector for Battery, ESC and Charger Lead.
Categories: Connectors, XT90, Anti-Spark, Antispark
− Molex 14-16AWG socket contact pin Gold (0194200003)
Can be used with the female side of molex connectors. Gold ones are not necessary, but may provide improved conductivity in application such as power or motor phase wires.
Categories: Connectors, Connector Pins, Molex
− SwitchCraft 6 Pin Female Plug (EN3C6FX)
6 Position Circular Connector Plug, Female Sockets Solder Cup. Generally used for Hall Sensor and Footpad connectors in VESC and FM XR boards. SwitchCraft 6 Pin Female Plug (EN3C6FX).
Categories: Connectors, SwitchCraft, Hall Sensor Connector, Footpad Connector
− Molex 14-16AWG Male Pins (0194170027)
Male pins that can be used with Molex Male mount connectors. You will need to get a different gauge if using with smaller or larger wires. Molex 14-16AWG Male Pins (0194170027)
Categories: Connectors, Connector Pins, Molex, Molex Pins
− Molex 18-22AWG socket contact pin (0194200002)
Can be used with female side of molex connectors. This is the one for smaller gauge wires. Molex 18-22AWG socket contact pin (0194200002).
Categories: Connectors, Connector Pins, Molex, Molex Pins
− 20 Pair XT60H Bullet Connector Plug (Male & Female)
xt60 Power connector. Always check polarity. Amass 20 Pair XT60H Bullet Connector Plug Upgrated of XT60 Sheath Female & Male Gold Plated for RC Parts.
Categories: Connectors, XT60
− Molex 16 pin Female Receptacle Housing (0194180030)
Housing used on stock FM XR harness. Molex 16 pin Female Receptacle Housing (0194180030)(WM4311-ND)
Categories: Connectors, Molex
− Uninsulated Butt Connectors Kit 300pcs 22-10 Gauge
Useful for joining multiple smaller awg wires to a larger awg wire. Truthfully you most likely will use the 10-12awg or 14-16 awg the most. This kit just happens to have those sizes as well. Would be more econimical to only purchase the sizes you need most. AIRIC Uninsulated Butt Connectors Kit 300pcs 22-10 Gauge Electrical Wire Seamless Non Insulated Crimp Terminals 12-10/16-14/22-16 AWG.
Categories: Connectors, Butt Connectors
− SwitchCraft 8 Pin Male Connector mount (EN3P8MX)
I have used these to run CAN wiring back to my battery box or wiring for lights. Various use cases. See this custom Flowglider box on THINGIVERSE. SwitchCraft 8 Pin Male Connector mount (EN3P8MX)
Categories: Connectors, SwitchCraft
− JST Connector Kit with 22AWG Pre-Crimped Wires
Another JST kit, but this one has precrimped ends if you prefer not to have to crimp the ends yourself. You can cut and solder to join them where needed. Tcenofoxy PH 2.0mm JST Connector Socket Kit with 22AWG Pre-Crimped Cables Wire 2/3/4/5/6/7/8/9/10 Pin Housing JST Adapter Cable Connector Socket 10 Colors Wire.
Categories: Connectors, JST
− Molex 14-16AWG socket contact pin (0194200001)
Can be used with the female side of molex connectors. Molex 14-16AWG socket contact pin (0194200001).
Categories: Connectors, Molex
− ESP8266 NodeMcu Mini chip (5pcs)
Used for OWIE implementation when doing a conversion utilizing a FM BMS. There are other chips out there, but I have had the best luck with these. ACEIRMC ESP8266 ESP-12 ESP-12F NodeMcu Mini D1 Module for WeMos Lua 4M Bytes WLAN WiFi Internet Development Board Base on ESP8266 ESP-12F for Arduino,Compatible with WeMos D1 Mini (5pcs).
Categories: PCB, Arduino, OWIE, FM BMS
− 100V 10A Schottky TO220 Diode (STPS20S100CT)
Diode I use when I need to keep voltage/current off the XLR charge pins in scenarios where the charge/discharge path are shared.
Categories: Electronics Components, Diodes, TO-220
− 12 Pack TO-220 Heatsink + Insulator/Mounting Kits
I primarily use this with diodes that I use when installing a Zbattery ZBMs or any charge/bms setup where the charge/discharge wires are shared to keep voltage/current off the XLR pins. Can be used with any component that supports TO-220 mounting. Easycargo 12 Packs TO-220 Heatsink + Insulator/Mounting Kits for LM317 LM317t L7805 L7812 L78XX Voltage Regulator, IRF Z44N 3205 520N 630 1404 MOSFET Transistor (20mm x 15mm x 10mm) (Silver 12 Pack)
Categories: Electronics Components, Heat Sinks, Diode Heat Sink, TO-220
− Littlefuse 10A 125V DC Fuse
The fuse that I use coming off of the positive pin of charge XLRs. Just to ensure that no one ever attempts to push more than 10A into the positive charge path on the XLR port. Littlefuse 10A 125V DC Fuse.
Categories: Electronics Components, Fuses
− 8 Pack Heavy Duty Floating Shelf Brackets
These brackets are great for building wall mounts for placing/storing your OneWheels/VEXRs. 8 Pack - White 9.25"L x 6"H x 1.5"W J Lip Shelf Bracket Rustic Industrial Farmhouse Iron Metal Wall Floating Shelf Bracket Metal Shelf Bracket, Industrial Shelf Bracket, Shelf Supports with Screws.
Categories: Brackets, Board Mount, OneWheel Wall Mount
− J-B Weld PlasticWeld - Quick Setting
Plastic weld. Useful for repairing cracked plastics. I have used this to secure inserts that had broken free in bumpers and many other things. J-B Weld 50132 PlasticWeld Quick-Setting Epoxy Syringe - Translucent Yellow - 25 ml.
Categories: Adhesives, Plastic Repair
− WELD-ON 4 Acrylic Adhesive
Adhesive. Various use cases. Check the datasheet to see what all it binds to. I have used this for bonding polycarbonate to ABS. WELD-ON 4 Acrylic Adhesive - 4 Oz and WELD-ON Applicator Bottle with Needle.
Categories: Adhesives, Solvents, Glue
− 100 Pieces M3 Plastic Nylon Flat Spacer Washer (M3 (ID)6mm (OD)1mm (Thickness))
Nylon washers. I generally use these above and below when mounting Lil FOCers to lid or plates with a thermal pad thicker than 1.0mm. 0.5mm washers (also in this list) are probably better for 1mm thermal pads to allow some compression. 100 Pieces M3 Plastic Nylon Flat Spacer Washer (M3 (ID)6mm (OD)1mm (Thickness)).
Categories: Hardware, Washers, Nylon Washers
− 10-32 Brass Threaded Inserts for Plastic (Longer)
Long inserts that can be used on flowglider boxes for the through hole insert holes further from the wheel that the 1/8 allen screws connect to. E-Z LOK Threaded Insert for Plastic Straight Flanged Brass Thread Inserts 10-32 Pack of 50.
Categories: Brass Inserts, 3D Printed Controller Box
− 10-32 Brass Threaded Inserts (5.7mm Length)
Short inserts that can be used on flowglider boxes for the shallow insert holes near the wheel that the 1/8 allen screws connect to. [ J&J Products ] Brass Insert IUB-032, 10-32 Tapered, Thru-Threaded, 7.5 mm OD, 5.7 mm Length, Heat Staking Inserts, 40pcs.
Categories: Brass Inserts, 3D Printed Controller Box
− Flush-Mount Press-Fit Nut for Sheet Metal 10-32 Thread Size
Press-fit nut inserts for replacing stripped threads in XR rails. Flush-Mount Press-Fit Nut for Sheet Metal 10-32 Thread Size, for 0.125" Minimum Panel Thickness.
Categories: Thread Repair, Hardware
− 100Pcs M3 x 0.5mm 304 Stainless Steel Self-Lock Nylon Lock Nuts
M3 locking nuts. Good to just have some extra of these on hand. Useful for mounting Lil FOCer. 100Pcs M3 x 0.5mm 304 Stainless Steel Self-Lock Nylon Inserted Hex Lock Nuts, Self Clinching Nuts.
Categories: Hardware, Nuts, Lil FOCer
− 260 Pcs M3 Stainless Steel Hex Socket Flat Head CounterSunk Bolts and Nuts Assortment
M3 bolt/nut assortment. Useful for many different projects and good to have extras for flowglider implementation with lil focer. 260 Pcs M3 Hex Socket Flat Head Countersunk Bolts Screw Nut Assortment Kit-304 Stainless Steel.
Categories: Hardware, Nuts, Bolts
− Nylon Flat Washers 6mm OD M3 ID 0.5mm Thickness
Nylon washers. I generally use these when mounting Lil FOCers to lid or plates. These go between the MOSFETs and the lid. Best used with a 1mm thermal pad. Nylon Flat Washers 6mm OD M3 ID 0.5mm Thickness.
Categories: Washers, Nylon Washers, Controller Mounting, Lil FOCer
− 1 Inch 3:1 Ratio Waterproof Clear Heat Shrink Tubing (4ft)
Large 1 inch clear tubing that I generally cut to size as needed. Fits well over OWIE, Buzzer, Etc. XHF 1 inch (25mm) 3:1 Waterproof Clear Heat Shrink Tubing Marine Grade Wire Cable Adhesive Lined Tube Insulation Seal Against Moisture Corrosion and Air Leakage, 4 Ft.
Categories: Heat Shrink, Heat Shrink Tubing
− 1 Inch 10 Ft XHF 3:1 Waterproof Heat Shrink Tubing Roll Marine Grade
Large 1 inch tubing that I generally cut to size as needed. Fits well over OWIE, Buzzer, Etc. 1 Inch 10 Ft XHF 3:1 Waterproof Heat Shrink Tubing Roll Marine Grade Adhesive Lined Heat Shrink Tube, Insulation Sealing Oil-Proof Wear-Resistant Black.
Categories: Heat Shrink, Heat Shrink Tubing
− Mini ESP32 ESP-WROOM-32 WLAN WiFi+Bluetooth IoT NodeMcu Arduino (3 pcs)
The brain of RESCUE DIY if you want to build your own lighting solution. See the RESCUE github for more info. Teyleten Robot D1 Mini ESP32 ESP-WROOM-32 WLAN WiFi+Bluetooth Internet of Things IoT Development Board for Arduino NodeMCU
Categories: Lights, PCB, Rescue
− DC Buck Converter, 9-120V to 5V 3A Step Down Variable Volt Regulator High Power Step Down Volt Transformer
Can be used to step down voltage from the main battery to 5v and used for lights. (RESCUE DIY). DC Buck Converter, 9-120V to 5V 3A Step Down Variable Volt Regulator High Power Step Down Volt Transformer
Categories: Lights, PCB, Rescue, DC Voltage Regulator, DC Buck Converter
− Permatex 22058 Dielectric Tune-Up Grease, 3 oz. Tube
A grease that is good for sticking onto stubborn connectors like the 16 pin molex or the 6 pin molex. Permatex 22058 Dielectric Tune-Up Grease, 3 oz. Tube.
Categories: Lubricant, Lube, Grease
− Plastic Storage Organizer Box with Removable Dividers (4 boxes)
Good bins for organizing small connectors and parts. I use these to hold xt60, xt90, mr30, etc. Sougayilang Fishing Tackle Boxes - 3600 3700 Plastic Storage Organizer Box with Removable Dividers - Fishing Tackle Storage - 4 Packs Transparent Tackle Trays
Categories: Organization, Storage
− Closed Cell Foam Neoprene Rubber Sheets
Great for padding batteries, battery boxes, or anything else. Can also be used as a water proof gasket/seal when cut as needed. Foam Sheets Self Adhesive Closed Cell Foam Neoprene Rubber Sheets Insulation Anti Vibration Foam Rubber Pads with Adhesive, Black (12" x 8" x 1/8", 5).
Categories: Padding, Closed Cell Foam, Neoprene, Vibration Reduction
− 10Pcs XT90E-M Male Plug Gold-Plated Mountable with Dust Sleeve
Good for use with custom controller boxes that want to utilize a custom harness and an anti-spark xt90 where the battery harness plugs into the controller box. See this custom flowglider box on THINGIVERSE.
Categories: Connectors, Ports, Mounted, XT90, VESC Controller Box, 18s, 19s, 20s
− 3 Pcs PG13.5 Cable Gland Stainless Steel Waterproof Connector
Cable gland that will work for torquebox, but it is very tight. Check for compatibility. uxcell 3 Pcs PG13.5 Cable Gland Stainless Steel Waterproof Connector Fastener Locknut Stuffing for 6-12mm Dia Wire.
Categories: Cable Gland, Connector, Ports
− M20x1.5 Cable Gland
Cable gland that will work with stock XR battery box, Floatboxx adapter, and Torquebox. The 53112120 is a SKINTOP® MSR-M M20 x 1.5 Cable Gland made of brass with nickel plated finish, polyamide insert, CR sealing and Perbunan (NBR) O-ring. Skintop® MSR offers high reliability and quality at an economical price. Suitable for use with reducing seal insert, to seal cables with smaller outer diameter.
Categories: Cable Gland, Connector, Ports
− Permatex 81730 Flowable Silicone Windshield Glass Sealer, 1.5 oz. (2 Pack)
Flowable silicone that is good for waterproofing controller and battery box entry points. I use it around ports and plugs mostly. Permatex 81730 Flowable Silicone Windshield Glass Sealer, 1.5 oz. (2 Pack).
Categories: Sealant, Waterproofing, Badgering, Silicone
− Permatex 82180 Ultra Black Maximum Oil Resistance RTV Silicone Gasket Maker
Decent liquid gasket repair/maker. I have rarely used this, but comes in handy from time to time. I used this to seal my first superflux motor. Permatex 82180 Ultra Black Maximum Oil Resistance RTV Silicone Gasket Maker, Sensor Safe And Non-Corrosive, For High Flex And Oil Resistant Applications 3 oz.
Categories: Sealant, Liquid Gasket, Water Proofing, Badgering
− Liquid Electrical Tape
Liquid electrical tape that can be used to repair mild nics or small cuts in wires. Can layer it on for thickness. STAR BRITE Liquid Electrical Tape - 4 FL Oz Can With Applicator Brush Cap - Protective, Airtight, Waterproof, Flexible, Dielectric Coating - Indoor & Outdoor Use.
Categories: Sealant, Insulator Repair, Wire Repair
− Kester 24-6337-0027 Solder Roll, Core Size 66, 63/37 Alloy, 0.031" Diameter
Decent solder that I use. Kester 24-6337-0027 Solder Roll, Core Size 66, 63/37 Alloy, 0.031" Diameter.
Categories: Soldering, Solder
− High Temperature Kapton Tape Assortment
Kapton tape is high temp tape. Can be used in a lot of various scenarios. On back of PCBs, BMS, etc. I have also just used it to hold down wires in battery boxes. MYJOR High Temperature Kapton Tape, Polyimide Tape, Professional for Protecting CPU, PCB Circuit Board, No Residue.
Categories: Tapes, High Temperature Tape
− Thermal Pad, 90x50x1.5mm, 12.8 W/m.K Thermal Compound Pad
One option of a decent thermal pad that will work for mounting lil focer to lid or metal plate. Plenty of options, but shoot for least 12W/m.K. This one is 1.5mm thickness and can be used with 1mm nylone washers as a buffer between the MOSFETs and the lid. Cut room for the washers into the thermal pad. Thermal Pad, 90x50x1.5mm, 12.8 W/m.K Thermal Compound Pad, Thermal Conductivity Gap Filler, Heatsink Cooling Pad All Coolers, CPU, GPU, IC Processor, 3D Printer, Raspberry Pi.
Categories: Thermal Pads, Little FOCer BYOH, Lid Mount
− Thermal Pad 14.8 W/mK, 120x120x1.0mm(1 pcs) Silicone Thermal Pads Non Conductive Heatsink Cooling Pad
One option of a decent thermal pad that will work for mounting lil focer to lid or metal plate. Plenty of options, but shoot for a 1mm pad with at least 12W/m.K. This one is 1mm thick and you can use 0.5mm nylon washers with it as a buffer between the MOSFETs and the lid. Cut room for the washers into the thermal pad. Thermal Pad 14.8 W/mK, 120x120x1.0mm(1 pcs) Silicone Thermal Pads Non Conductive Heatsink Cooling Pad, Highly Efficient Heat Resistant Soft Pad for Laptop Heatsink/SSD/CPU/IC/LED Cooler.
Categories: Thermal Pads, Little FOCer BYOH, Lid Mount
− Spray On Silicone Conformal Coating, Clear
Useful for waterproofing electronics. This is the spray on modified silicone conformal coating. There are other types. MG Chemicals - 422B-340G 422B Silicone Conformal Coating, Clear, 340 gram Aerosol.
Categories: Silicone, Waterproofing, Badgering, Conformal Coating
− Silicone Conformal Coating Liquid
Useful for waterproofing electronics. Also usefule for waterproofing all the ports ( just drip it in and let it dry, but keep it off the pins). MG Chemicals - 422C-55MLCA 422C Silicone Conformal Coating 55 mL Bottle
Categories: Silicone, Waterproofing, Badgering, Conformal Coating
− 22 AWG 4 Conductor Stranded Shielded Plenum Cable White (100ft)
A decent shielded 22AWG 4 conductor that can be used for CAN 5v, GND, Hi, Lo. Can also be used to make new XR headlight cables. Useful in many scenarios. Custom Cable Connection 22 AWG 4 Conductor Stranded Shielded Plenum Cable White CL3P Jacket for Security/Alarm/Access Control/Sound - 100 Foot Roll in a bag
Categories: Wire, Wiring, CAN Bus, XR Headlight Cable
− 24 Gauge Wire - 6 Colors Tinned Copper Wires with Silicone Rubber Insulation (Black, Red, Yellow, Green, Blue, White) 30ft / 9m Each
A decent set of 24 awg silicone wire. Useful for OWIE chip installations as well as other use cases. 24 Gauge Wire - 6 Colors Tinned Copper Wires with Silicone Rubber Insulation (Black, Red, Yellow, Green, Blue, White) 30ft / 9m Each - 24 AWG (OD: 1.6 mm) Stranded Hook Up Wires from Plusivo.
Categories: Wiring, Wire, Silicone Wire
− 18 Gauge Silicone Wire Spool 100 ft Flexible Stranded Tinned Copper Wire (Multiple Color Options)
18awg silicone wire that I frequently use for charge path wiring. BNTECHGO 18 Gauge Silicone Wire Spool 100 ft Black Flexible 18 AWG Stranded Tinned Copper Wire.
Categories: Wire, Wiring, Silicone Wire
− LITTLE FOCER REV3.1 ESC ELECTRIC SPEED CONTROLLER - BYOH
I personally think this is one of the best VESC Controllers out there for OneWheel VESC conversions. Bring Your Own HeatSink version. Requires mounting to lid or box with a termal pad to isolate the MOSFETs.
Categories: VESC, VESC Controller
− SRA Solder 135 Rosin Paste Soldering Flux For Electronics
SRA Solder 135 Rosin Paste Soldering Flux For Electronics, No Clean Flux Made for Lead and Lead-Free Solder Circuit Boards and Copper Electrical Wire - Safe Clean Residues with No Goopy Mess (2oz Jar)
Categories: Solder, Soldering, Flux